Three-function electric bed technical parameters
Function
Back lift 0-65°±5°; users can sit up independently, easily complete the daily life required to reduce the labor intensity of medical staff, reduce lumbar muscle strain.
Leg lift 0-30°±5°; Promotes blood circulation in the legs, prevents numbness in the limbs, etc., facilitates leg or foot care and speeds up the patient's recovery.
Back-Knee Linkage It can realize back and knee position linkage adjustment with one button, which is convenient, fast and efficient.
High and low lift 350~650mm±20mm; can assist medical personnel to do patient examination or care, effectively reduce the labor intensity of bending, prevent lumbar muscle strain; can be adapted to the use of other medical equipment height, such as transfer vehicle.
Manual CPR; Manual CPR switches are configured on both sides of the bedside, in case of emergency, the backboard can be quickly restored to the horizontal position within 5 seconds , which facilitates the resuscitation by medical personnel.
Emergency stop switch; the bed frame is equipped with an emergency stop switch, press the emergency stop button to suspend the operation of the medical electric hospital bed, to provide safety for emergencies.
One-touch reset: in case of emergency, the bed can be brought back to a horizontal position in any body position.
Electrical control section
Motor Adopting 3 DEWERT motors imported from Germany, the thrust is up to 6000N, high reliability, the protection level reaches IPX4 or above, and it has passed the certification of IEC and so on. (Provide certification)
Battery: In case of emergency power failure, the bed can be reset.
Hand controller: ergonomic design based on one hand, easy to control with one hand, using silicone buttons, high touch comfort, with a key reset function, configured with a mechanical lock function, can lock or open part of the operating function, further increase security.
Bed structure and components
Bed frame: The overall bed frame is made of high-quality steel tubes precision welded, the bed frame is made of 50*30*2.5mm rectangular tubes, with strong compression resistance and high load-bearing capacity, which can carry a static load of 400KG and a safe working weight of 240KG; the backboard, sitting board, leg boards and footboards are designed using a detachable independent frame to realize a four-section bed, and the dimensions are designed in accordance with human ergonomics .
Bed surface: the bed plate is made of 1.2mm cold-rolled steel plate with strip-shaped ventilation holes, beautiful appearance, strong pressure resistance, easy to clean and disinfect; both sides of the bed panel and the foot with non-slip block, preventing the mattress from slipping sideways.
Head and tailboard of the bed:
1. Bed end plate: Ergonomic, with leather surface for anti-slip and anti-fouling, designed in accordance with EU IEC-60601-2-52 standard.
2. Blow molding with HDPE material, easy to clean surface, overall impact resistance, heat resistance, low temperature resistance, chemical resistance; built-in stainless steel pipe, solid and sturdy.
3. Installation with the bed frame adopts the way of quick unplugging and insertion, which can be quickly disassembled and installed to meet the needs of emergency resuscitation.
Guardrail: three-section translational guardrail, the overall design conforms to IEC60601-2-52 safety standards, the guardrail is lower than the mattress when it is put down, and the main body is made of high-quality cold-rolled steel tubes, which does not take up any space when the fence is contracted to improve the utilization rate of the ward space.
Anti-collision wheels: the 4 corners of the bed are equipped with anti-collision wheels, which are protruding outside the bed, and can effectively prevent the bed from colliding with elevators, door frames and other planar obstacles in the process of implementing the use of the bed to ensure a smooth transition of the bed.
Casters: Configuration of four double-sided center control casters, diameter 125mm, mute and wear-resistant, hard and lightweight texture; center control brake pedal a foot brake, bilateral landing solid and reliable.
Each side of the bed frame is equipped with 2 accessory hooks, which can hang medicine bags, drainage bags and dirt bags, etc.; the bed is equipped with a total of 4 infusion stand jacks at the head and tail of the bed, which is convenient and concise, and does not take up space.
Arts And Crafts
1. The steel frame parts are molded in one piece, which is firm, safe and reliable; the plastic parts are molded by injection molding, blow molding, blister molding and other processes, which has soft and beautiful appearance lines, and the overall strength is reliable, durable and easy to clean;
2. High-precision welding process ensures that the hospital bed is safe, reliable and strong;
3. Surface coating adopts double-coating technology, electrostatic spraying after oil removal, rust removal and environmental protection silane skin film agent treatment, the surface electrostatic spraying material has a perfect appearance and extremely strong chemical resistance and electrical insulation, spraying material is non-toxic and mildew-resistant; the surface of the coating is glossy and bright, does not fall off, does not rust, and is anti-static. (Coating adhesion test report can be provided)
4. The whole assembly adopts special production line, each node can control the production process and product quality at any time;
5. Professional packaging is used to ensure the safety of product transportation.
Configuration
|
serial number |
Name of goods |
Quantity, units |
|
1 |
bed |
1 sheet |
|
2 |
headboard |
1 pair |
|
3 |
parapet |
2 pieces |
|
4 |
bedpan |
4 pieces |
|
5 |
Mute casters |
4 |
|
6 |
crash wheel |
4 |
|
7 |
Infusion Holder Jack |
4 |
|
8 |
attraction link |
4 |
Size
whole bed size (LxWxH): 2190×1020× (350~650)mm±20mm ;
Bed size: 1950×850±20mm.
